다울빛 이주여성 연합회

logo

한국어

정보마당

2019.10.31 11:34

한국국적귀화시험반

조회 수 1897 추천 수 0 댓글 1
?

단축키

Prev이전 문서

Next다음 문서

크게 작게 위로 아래로 댓글로 가기 인쇄 첨부
?

단축키

Prev이전 문서

Next다음 문서

크게 작게 위로 아래로 댓글로 가기 인쇄 첨부

귀화시험1.jpg

귀화시험3.jpg


다울빛이주여성연합회 
 
한국 국적귀화시험반 
 
오늘  2명이 빠졌네요..ㅠㅠ 
 
그래도 항상 열심히  하는 3명은 절때 빠지지 않는다~


?
  • ?
    Bella 2021.03.24 17:27
    Click here to buy FAG 1226 bearing. Eric Bearing LTD has enough stock for it.

    Rolling bearing precision components require corresponding caution when used. Not only does it change the use of high-performance linear bearings, but if they are not used properly, they cannot achieve the expected performance test results, so the following aspects of bearings are considered:
    1. Keep the bearing and its surroundings clean. Even invisible dust bearing smiles will increase Timken bearing wear, vibration and noise.
    2. When using installation, do not allow strong punching carefully, do not allow the use of hammer bearings, allow direct hit by rolling pressure.
    3. Use appropriate and accurate installation tools, the use of special tools, try to avoid the use of fabrics and staple fibers.
    4. To prevent the corrosion of NSK bearings, directly select the bearings by hand, fully wash the sweat on your hands, and apply high-quality mineral oil before starting, especially in the rainy season and summer, pay attention to rust.
    After the bearing is installed in the host, there is a measurement index called cyclic rotation accuracy. This kind of change approximately repeats that the required number of revolutions represents the "quasi-period" of the cyclic rotation accuracy, and the magnitude of the magnitude change within the quasi-cycle is large, that is, the cyclic rotation accuracy is poor.
    When proper preload is applied to the bearing spindle, this can gradually increase the speed to close to the working speed to implement the "run-in" effect of the linear bearing, which can improve the cycle rotation accuracy of the spindle.
    There is a precision instrument that improves the accuracy of NSK bearings. When the main shaft uses 6202/P2 type bearings, but its accuracy still can not meet the requirements, then thicken the journal and make a raceway on it to replace the inner ring, and the steel ball is accurately measured, and the size is set every three pieces , Each group of steel balls is separated by an interval of close to 120°, due to the reduction of a heavy processing surface and a reduction of a matching surface, and at the same time, the rigidity of the shaft-bearing system is improved, and the maximum three balls are close to the minimum three balls The equidistant distribution also improves the rotation accuracy of the shaft, thus meeting the accuracy requirements of the instrument.

List of Articles
번호 제목 글쓴이 날짜 조회 수
공지 다울빛 이주여성연합회 성과보고회겸 (송년회) 3 file admin 2017.12.28 19007
공지 ♣ 제 1회 부평구 다문화 축제 다울(다함께 사는 우리)축제 ♣ 2 file admin 2017.09.17 18852
공지 2017년 인생교실 프로그램 (한국인과 다문화가정 모두) file admin 2017.06.14 19384
공지 2017년 다울빛 이주여성 연합회 활동계획표 (6-11월) 3 file admin 2017.06.14 19716
공지 2017년 프로그램 안내 1 file admin 2017.01.22 18301
26 지역 농산물을 활용한 세계요리대회 신청 안내 file admin 2019.06.26 1365
25 한국어 중급반 수업 file admin 2019.06.26 1353
24 7월달 캘리그라피 수업 3차 file admin 2019.07.11 1592
23 7월달 밴드 활동 file admin 2019.07.11 1351
22 지역 농수산물을 활용한 세계요리대회 1 file admin 2019.07.23 1289
21 다울(다함께 사는 우리 축제)3회 행사 부스, 패션쇼 참가 안내 file admin 2019.07.23 1825
20 사랑의 빨간밥차 봉사자 모집합니다 2 admin 2019.08.06 2335
19 사랑의 빨간밥차 봉사활동 1 file admin 2019.08.06 2316
18 송편만들기 안내 file admin 2019.08.13 2105
17 2019.09.22 제3회 다울(다함께사는 우리)축제 1 file admin 2019.08.20 3245
16 2019. 09.22 제 3회 다울축제 공유 이벤트 안내 2 file admin 2019.09.04 2449
15 다울빛 이주여성 연합회와 함께하는 빨간 밥차 2 admin 2019.10.02 2769
14 2019 천사데이 나눔의짜장차 희망나눔축제 안내 2 file admin 2019.10.02 2597
13 다울빛 봉사단 모집 안내 1 file admin 2019.10.18 2097
12 2019.10.26 사랑의 쌀 나눔콘서트 안내 1 file admin 2019.10.21 1989
11 김포 연잎밥만들기 및 고구마케기 체험활동 2 file admin 2019.10.21 2087
10 결혼 이민자 소비자 교육 file admin 2019.10.30 2026
» 한국국적귀화시험반 1 file admin 2019.10.31 1897
8 다문화이해강의& 토론회 file admin 2019.10.31 1941
7 사랑의 쌀 나눔 file admin 2019.11.05 1929
Board Pagination Prev 1 ... 9 10 11 12 13 14 15 16 17 18 Next
/ 18